Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFI
Not supported
DJI Air Unit Connection Way
Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug
Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot
*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card.
BetaFlight Camera Control Pad
Yes(CC pad on the front side)
Current Sensor Input
Supported. For SpeedyBee BLS 50A ESC, please set scale = 386 and Offset = 0.
Power Input
3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output
9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
9V Output
2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
3.3V Output
Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output
Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal
M1 - M4 on bottom side and M5-M8 on front side.
UART
6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
ESC Telemetry
UART R5(UART5)
I2C
Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad
Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer
BZ+ and BZ- pad used for 5V Buzzer
BOOT Button
Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input
Supported. Named as RS on the front side.
Smart Port / F.Port
Not supported
Supported Flight Controller Firmware
BetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
Firmware Target Name
SPEEDYBEEF405V3
Mounting
30.5 x 30.5mm( 4mm hole diameter)
Dimension
41.6(L) x 39.4(W) x 7.8(H)mm
Weight
9.6g
Детальні характеристики:
Виробник
SpeedyBee
Модель
F405 V3 BLS 50A 30x30 FCESC Stack
Артикул
SB-F4V3-50-STACK/HP0008.0094
Мікроконтролер
STM32F405
Напруга
3-6 В
Постійний струм
50 А
Піковий струм
55 A
Розмір
30.5 х 30.5 мм
Вага
13.8 г
Країна виробництва
Китай
Гарантія, міс
6
Немає відеозаписів за таким запитом: Політний стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094).
Ремонт комп'ютерів у Києві: ремонт і обслуговування ПК, модернізація, діагностика і лагодження комп'ютерів за низькими цінами. Васильківська, 55, обслуговування, налаштування, комп'ютерна допомога вдома та в офісі недорого. Купити Політний стек SpeedyBee F405 V3 BLS 50A 30x30 FCESC Stack (SB-F4V3-50-STACK/HP0008.0094). Швидке заправлення картриджів для будь-якого принтера з гарантією якості від сервісного центру VPS Group по місту Києву. Купити тонер фасований. +38 (093) 290-17-17